Installation & Assembly Instructions
Please contact our Customer Service Division with any questions at:
30700 D Carter Street ∙ Solon, OH 44139 ∙ (P) 440.248.5480 ∙ support@tritonproducts.com
For a full line of products visit www.tritonproducts.com 1 INS3535
Read all instructions completely before installing. Should you have any questions about your installation, please call
Customer Service at 440-248-5480. Missing and damaged parts must be reported within 5 days from receipt of delivery.
Tools needed for this installation (Not Supplied with Kit)
Lever - Pencil or marker - Phillips head screw driver – Electric drill – ½” Standard drill bit for hollow wall installation –
Safety glasses – 5/16” Masonry bit for concrete block installation – 1/16” Standard drill bit for stud wall installation – Tape
measure
Parts Listing
P/N# Qty Description Qty
Hardware______________________
10-01815T 1 Top Track Sections 5 2-1/2” Toggle Bolts
10-0280-1T 2 Top Hang Rail with hanging Slots 6 3-1/2” Toggle Bolts
10-0280-2T 2 Bottom Hang Rail Section 11 White Plastic Wall Anchors
10-0280-3T 2 Hang Rail Connector with 2 bolts 11 2-1/4” Wood Screws
10-0480 1 31” Wire Shelf 11 Toggle Bolt Expanders
10-0336 1 Set Hanging Brackets for Wire Shelf 1 Hex Head Wrench for Hang Rails
10-0580 1 31” Combination Rail 10 Assorted LocHooks for Tool Board
10-0880 1 LocBoard Tool Board 3 Plastic Hanging Bins
10-1901 1 31” Wire Basket 3 Assorted Combination Rail Hooks
10-2001 1 Set Hanging Brackets for Wire Basket
We have included all mounting hardware for hollow and concrete block wall installations. It is not necessary to mount system
to wood studs. Each system will require 35 lineal Inches of wall space for mounting and a minimum ceiling height of 7-1/2 feet
high for proper clearance.
Drill Diameter Listing: Drill diameter sizing for hollow wall installations: Use 1/2” standard drill bit
Drill diameter sizing for concrete wall installations: Use 5/16” masonry drill bit
Drill diameter sizing for wood Stud wall Installations: Use 1/16” standard drill bit for pilot holes
Preparation for Top Track Installation: (Image A-1)
1. When installing in a corner, leave 1” space between side wall and your top track.
2. Determine the maximum height of storage you would like available above your system. (See Fig. A-1). For an 8 foot
ceiling; 78” off the floor leaves 18” of storage above and 81” leaves 15” storage above.
3. Using a tape measure, mark your desired height off the floor with a 4” long pencil mark.
4. (Refer to Fig. A-1 & A-2) Using a level, align top of top track with your pencil mark in step 3. With top track level, mark
the center of each hole’s location on your wall. (Note: Before starting to drill holes always make sure all screw hole
locations do not fall in line with electrical wires, duct work or plumbing inside of your wall. If a potential problem exists,
reposition and remark screw hole locations.)
5. (Fig. A-2) Drill hole locations marked using the correct drill diameter sizing and type listed above. Should you come in
contact with wood studs, stop and mark the hole with X and after drilling all other holes come back and drill these holes
using a 1/16” bit for pilot hole for wood screws.
Attachment of Top Track to Wall Surfaces: (Fig. A-3)
6. For hollow walls; (Fig. A-3) Use 2-1/2” long toggle bolts with expanders. Insert all toggle bolts through top track and
attach all toggle bolt expanders. Omit toggle bolts that fall in line with X or wood studs. Insert toggle bolts with
expanders into holes in wall before starting step 9.
7. For concrete walls; use white plastic wall anchors and 2-1/4” long wood screws. Install all plastic wall anchors in all hole
locations before starting step 9.
1785 - Storability® 33"L x 63"H Garage Storage System
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern